Kawasaki Teryx 4 Full Cab Enclosure (Sides & Rear Window) by SideXSide Enclosures

Kawasaki Teryx 4 Full Cab Enclosure with Rear Window by SideXSide Enclosures

This Kawasaki Teryx 4 full cab enclosure closes your four-seat machine in on three sides — both side panels plus a rear window, cut to work as one set. It mounts to the hard roof and works with whatever front windshield you run, because we stopped cutting openings for windshield brackets and now go right over them. That one change means a tighter seal and a panel that fits any windshield brand on the market. Choose your attachment style in the drop-down before ordering.

Key Features

• Complete coverage: side panels and rear window in one kit
• Fits all Teryx 4 trim levels
• Installs over windshield brackets — no cutouts, so the cab seals tighter
• Works with any windshield brand, factory or aftermarket
• Mounts to your existing hard roof and front windshield
• Velcro sewn along most edges so you choose the attachment points
• Three attachment styles: self-adhesive Velcro, self-adhesive snaps, or screw-in snaps
• Built for cold weather and job site conditions
• Sewn in Eastern Ohio and backed by a 1-year quality and workmanship warranty

Fitment

• Kawasaki Teryx 4: all trim levels, fits through 2026+
• Four-seat Teryx 4 models
• Requires a hard roof and front windshield on the machine

Check Your Roof Before You Order

Most Teryx 4 roofs have a rear lip — where the rear window mounts — that runs straight up. A few roof models are built differently: the lip goes up and then turns outward about a quarter inch. If yours is the second kind, you have two ways to go:

• Trim method (what most customers pick): trim off the outward quarter-inch lip so the standard J-clip attaches the way it was designed to.
• Velcro setup (no modification): tell us when you order and we will swap the J-clip for Velcro. You then apply the included self-adhesive Velcro to the underside of your roof.

Not sure which roof you have? Call before ordering and we will walk you through it.

Important Fitment Notes

• Includes side panels and rear window. A roof and windshield are not included.
• No windshield bracket cutouts. If one of the straps lands on a bracket, cut that strap and use the next one — the remaining attachment points carry the panel.
• Self-adhesive Velcro and self-adhesive snaps are not guaranteed to bond to every surface. Screw-in snaps give the most positive attachment.
• Adhesives may damage decals, especially when applied directly over them.
• Compatibility with aftermarket accessories such as mirrors, light bars, and speakers is not guaranteed.
• Use small Velcro sections rather than long strips for better adhesion.
• Do not trailer the machine with the enclosure installed. Trailering voids the warranty.

Specifications

• Coverage: both side panels plus rear window
• Vehicle fit: Kawasaki Teryx 4, all trims, through 2026+
• Required equipment: hard roof and front windshield
• Windshield compatibility: any brand — installs over brackets, no cutouts
• Rear window mounting: J-clip to the roof lip, or Velcro on request
• Attachment options: self-adhesive Velcro (no drilling), self-adhesive snaps (no drilling), or screw-in snaps (drilling required)
• Velcro placement: sewn along most edges for flexible mounting
• Warranty: 1 year on quality and workmanship

Real Life Value and Uses

• Seal all four seats in so the back row is not taking wind the whole ride.
• Keep the cab warmer on early starts without adding a hard cab.
• Stop rain and sleet from soaking the seats on a long day of work.
• Block dust pulled in from behind on dry trail and gravel.
• Run the machine through job site work and winter chores instead of parking it.
• Keep the same enclosure if you change windshields later — no cutouts to match.
• Protect gear stowed behind the rear seats from weather and road spray.

Why Choose SideXSide Enclosures

• Over 30 years in the canvas business, building UTV enclosures since 2008
• Bracket-free design that fits any windshield instead of one specific brand
• Two mounting solutions for the roof lip variation, including free Velcro on request
• Designed and sewn in Eastern Ohio
• Call in and you will usually reach the owner who drew the pattern
• 1-year warranty, repaired or replaced at our discretion

Take a look at your roof lip, pick your attachment style, and close your Teryx 4 in from the sides to the rear window — call us if you want a hand confirming which roof you have.